Martindale Instruments

Martindale was founded in 1928 and has been manufacturing test equipment continuously since that time. As an approved stockist of Martindale Electric, Glanford Electronics Ltd can supply, repair and calibrate Martindale's range of test equipment. We would be pleased to give advice on which test equipment would suit your needs.

Martindale Micropat Plus Bundle

The Martindale Micropat Plus Bundle includes labels, software, download lead and a barcode reader to speed up testing & prevent errors, as well as 1000 combined barcode and test labels and a packet of fail labels.

A set of 3-phase adaptors allows 3-phase equipment to be tested.

The IEE Code of Practice gives full guidance on PAT test theory and practical tips.
This kit has everything needed to start testing straight away.

HPAT600 Hand Held PAT for faster testing

The HPAT600 offers profitability gains for service companies and productivity gains for health & safety officers, premises & facilities managers and other users, for example school caretakers.
Battery powered for lightweight and easy use, it’s supplied with mains leads and a car charger, crammed with features such as dual insulation test voltage, user selectable pass levels, easy (manual) or fast (automatic) operating mode, IEC lead test insulation, polarity, backlight, test lead null out feature, simulated load test and test data storage for up to 200 appliances - equivalent to a whole day’s testing.
It tests class I, class II appliances and power cords. It incorporates a 250V insulation test for sensitive IT equipment and appliances with mains filters. A 200mA DC earth continuity test is safe for all appliances and complies with the new code of practice for PAT testing. Limits can be set by managers to suit their own requirements eg. to identfiy appliances without borderline passes.

In manual mode, a connection diagram for the selected test type is shown on the display. Each step of a test requires user confirmation by a press of the OK button. In the automatic mode, it will quickly run through a selected test sequence without any further user interaction unless a failure is encountered.
All these features make it the PAT of choice for implementing an efficient and cost effective portable appliance testing solution. Complete with free Certificate of Calibration..

The HPAT600 is a battery powered portable Appliance Tester with the following features:-

Dual Insulation Test Voltage - The insulation measurement test voltage can be set to either 500V or 250V.
User Selectable Pass Levels - Appliance test pass levels may be user defined.
Easy or Fast Operating Modes - The HPAT600 can be operated in either of two modes. In manual mode, aimed at the newcomer to PAT testing, a connection diagram for the selected test type is shown on the display. Each step of a test requires user confirmation by a press of the OK button.
In the Auto mode, for the experienced operator, the HPAT600 will automatically run through a selected test sequence without any further user interaction unless a failure is encountered.
IEC Lead Test - The HPAT600 can also be used to check IEC leads for earth continuity, insulation, and polarity.
Test Data Memory Storage - The HPAT600 is able to store test data for up to 200 appliances into memory.

Now Available!

Martindale Veritest 2230
The VERITEST 2230 is being offered at a very special price that just cannot be missed. This all in one tester,ideal for Part P requirements, incorporates continuity, insulation resistance, RCD,non trip earth loop impedance, and phase rotation tests. This unit is smaller and more compact than other machines on the market, which makes it very comfortable to use in confined areas. Although supplied in a carry case which allows hands free use, the unit can also be comfortably held in one hand.

Specifications

Insulation Ranges:
0.05MOhms to 1999Ohms at voltages between 50VDC, 100VDC, 250VDC, 500VDC, 1000VDC with a resolution of 0.01MOhms,0.1MOhms & 1MOhm.
Continuity Ranges: 0.01Ohms-19.99Ohms (0.01Ohms res) 20.0-99.9Ohms (0.1Ohms res)
RCD Ranges:
10ma, 30ma, 100ma, 300ma, 500ma.
Non Trip Earth Loop Ranges: 0.034-19.99Ohms (0.01Ohms res), 20.04-199.9Ohms (0.1Ohms res), 2004-1999Ohms (1S2 res)
Phase Rotation Test: Yes
Weight: (batteries included) 1000gm
Dimensions: 222mm(L), 162mm(W), 57mm(D)
Working Temperatures: -10°Cto+50°C
Live Circuit Warning: Yes
Supplied complete with test leads, soft carry case & Quickstart user guide as well as a comprehensive user manual

   Veritest 2240 All in one Tester
We are proud to introduce the VERITEST 2240 to the Martindale range of test equipment. This all in one tester incorporates continuity, insulation resistance, RCD, earth loop impedance, global earth resistance and phase rotation tests. This unit is smaller and more compact than other machines on the market, which makes it very comfortable to use in confined and hazardous areas. Although supplied in a carry case which allows hands free use, the unit can also be comfortably held in one hand. The Veritest also has the ability to commit test results to its internal memory and is equipped to download to a P.C. via optional software and accessories.

Specifications

Insulation Ranges:
0.1 Ohms to 1999Ohms at voltages between 50VDC, 100VDC, 250VDC, 500VDC, 1000VDC with a resolution of 0.01Ohms,0.1Ohms and 1Ohms
Continuity Ranges: 0.01Ohms-19.99Ohms (0.01Ohms res) 20.04-99.9Ohms (0.1Ohms res)
RCD Ranges:
10ma, 30ma, 100ma, 300ma, 500ma.
Non Trip Earth Loop Ranges: 0.034-19.99Ohms (0.01Ohms res), 20.04-199.9Ohms (0.1Ohms res), 2004-1999Ohms (1S2 res)
Global Earth Resistance Range: 1-1999Q
Memory Slots For Saved Tests: 350
Phase Rotation Test: Yes
Weight: (batteries included) 1000gm
Dimensions: 222mm(L), 162mm(W), 57mm(D)
Backlight: Yes
Working Temperatures: -10Cto+50C
Live Circuit Warning: Yes
Veritest 2250 All in one Tester
This is our flagship multi tasking all in one 17th edition tester. Incorporating all of the functions of the VERITEST 2240, with the added functionality of a power analyser and earth resistivity and environmental tests, such as temperature, relative humidity, air speed, illuminance and sound level which can be carried out with additional accessories (purchased separately). This is a fully specified machine that not only offers powerful testing capabilities to the electrician, but also is an invaluable tool for power, distribution, environmental and cabling organisations alike.

Main Features

Continuity Test
Insulation Resistance Test
Non Trip Earth Loop Test
RCD test
Phase Rotation Test
Power Analyser
Earth Soil Resistivity
999 Memory Slots
Downloadable to PC
Backlight
Auto Power Off
Carry Case

General Purpose Multimeter MM34
This new, low cost multimeter has 4 main functions together with diode and battery test and a large clear display. The sculpted shape makes it comfortable to hold and easy to position the central rotary switch.

Specifications
General Purpose Multimeter MM34
31/2 digit LCD display with automatic polarity indication and automatic zero.
AC V: 100mV to 600V (2 ranges) (50Hz to 500Hz)
DC V: 1 mV to 600V (4 ranges)
DC A: 0.1 pA - 10A (5 ranges)
Ohms: 10m4 to 20MΩ (5 ranges)
Diode test
Battery test:1.5V & 9V
Dimensions: 143 x 68 x 47mm
Includes: test leads, battery and user manual.

Digital Clampmeter CM51
The Martindale CM51 is a low cost 200A mini clamp meter with autoranging,display hold and auto power down. The two ranges mean that when measuring 40A and lower currents the resolution increases from 100mA to 10mA. Autoranging ensures that the most suitable range is always automatically selected.
This small current clamp will fit into your shirt pocket for maximum convenience.
The small jaws make it easy to use and the 200A AC range accurately covers the majority of applications.

Specifications

3½ digit LCD display with anunciators
Display hold DH button
Display update 25 times per second
AC A: 10mA to 200A,
autoranging (2 ranges)
(40Hz to 500Hz)
Max conductor: 27mm Ø
Operating temperature: 0° to 40°C at <80% RH
Auto Power off after 10 mins
Low battery warning: “BAT” symbol
Overrange indication: “OL” symbol
Dimensions: 150 x 52 x 24mm
Weight: 110g
Overvoltage: Category III, 300V
Includes: battery, carry case and user manual
With Free Calibration Certificate.

Digital Insulation Tester IN2001
The IN2001 insulation tester is amazing value for money. With an automatic zero adjust feature to remove the resistance of the leads, you are guaranteed fast, accurate continuity testing at 200mA. The IN2001 has a stable 500V test voltage and a 200mA continuity test, fully meets all relevant regulations: BS7671, HD384 and BS EN 61557.This supercedes the Metrohm I6D500 Single range tester This supercedes the Metrohm 16A500

Specifications
Insulation: 10kohms to 100Mohms at 500V
Continuity: 0 - 200ohms, 0.01ohms resolution (audible tone <1ohm)
Voltage range: 500V AC
Complies with: BS EN 61557 and 17th Edition
Dimensions: 190 x 90 x 54mm
Includes: quality soft protective carry case, test leads, battery and user manual.

17^th EDITION INSTALLATION TESTERS
IN2003 Insulation Tester
The IN2003 insulation and continuity tester gives 250, 500 & 1000V tests. The top of the range IN2003 insulation tester comes with all the facilities you need to do professional testing. With an automatic zero adjust feature to remove the resistance of the leads, you are guaranteed fast, accurate continuity testing. The three test voltages allow you to carry out the widest range of testing. A major advantage of this design is that you can set the test button to be either latching to give a permanent output or 'press to test' with the option of switching between these two ways of working at any time. A professional product for professional electricians!

Specifications
Insulation test at 250 / 500 / 1000V.
0-200Ω continuity range (buzz <1Ω), 0.01Ω resolution.
0-100MΩ (500V) 0-200MΩ (1000V).
500V AC range.
Complies with BS EN 61557 (16^th Edition).
Dimensions: 190 x 90 x 54mm.
Replacement leads - order code: TL47.
Optional fused test leads - order code: TL57.
Supplied with batteries, instructions, quality case and leads.
LP2000 Loop Tester
The LP2000 is a fast and accurate autoranging loop tester and is the lowest cost 16^th Edition earth loop impedance tester available. It can carry out phase earth and phase neutral testing and it automatically displays PSC readings. A wander lead for testing bonded metalwork is also supplied.

Specifications
Range: 0.01 to 200Ω (Autoranging).
Resolution: 0.01 and 0.1Ω
Ipsc: 0-19.99kA in steps of 0.001 kA (10A).
Dimensions: 190 x 90 x 54mm.
Complies with BS EN 61557 (16^th Edition).
With case, standard mains lead and wander lead.
Optional leads for testing at distribution boards and luminaries TL85 or TL88.
RC2000 RCD Tester
The RC2000 is a very fast and easy to use RCD tester, suitable for all common RCDs. All you need to do is select the test current and then swap between half the current, when the trip should stay open and the test current itself, when the RCD should trip. A second toggle switch allows you to test, as required, for opposite sides of the current cycle.

Specifications
Full trip settings: 6mA-10-30-100-300-500mA.
Half trip settings: 3mA-5-15-50-150-250mA.
Fast trip settings: 150mA (full trip of 6, 10 and 30mA only).
Switchable selection of test cycle 0 / 180°.
Timing range: 0 - 1999mSec in steps of 1 mSec.
Timing accuracy: ±2% of reading ±1 digit.
Dimensions: 190 x 90 x 54 mm.
With case and 13A mains lead.
Optional lead for distribution boards - order code: TL88.
Complies with BS EN 61557 (16^th Edition).

CM56 1000 Autoranging clamp
The CM56 has a large display combining a clear 3¾ digit readout with a responsive 34 segment bar graph which indicates fluctuating readings. For general purpose measurements it has autoranging AC and DC voltage and measures resistance to 30MΩ with a beeper on the low resistance continuity range. It also measures frequency with 0.1 Hz resolution allowing accurate determination of mains or generator frequencies. Hold and AC peak functions assist in taking readings in awkward places.

Specifications
AC Current: 0-32-320-1000A.
AC Volts: 0-3.2-32-320-600V autoranging.
DC Volts: 0-320m-3.2-32-320-1000V autoranging.
Resistance: 0-320-3.2k-32k-320k-3.2M-30MΩ
Frequency: 0-320-3.2kHz-32kHz.
Max. conductor: 57mmØ or 70 x 18mm bar.
With carry case and leads.
PC15250 Phase Rotation & Continuity Indicator
The PC 15250 continuity indicator will quickly and simply prove continuity of all three lines, or identify which are faulty and it also shows the sequence of phase rotation.
A fast, effective method of identifying worn or unmarked cables, and ensuring all 3-phase outlets and machinery are wired correctly.
The retractable probe shields give a choice between long exposed tips for reaching inaccessible contacts and safer, shorter lengths of bare tips for increased safety.
Supplied with one fused crocodile clip and two fused prod type probes with retractable shrouds this unit is fully compliant with GS38 and BS EN 61010.

Features Include:
Proves continuity
Identifies fault lines
Phase rotation
   EasyPat1600 Manual Portable Appliance Tester
Martindales EasyPAT 1600 Manual PAT Tester, is a cost effective and easy to use tester for anyone who just needs to the minimum to comply with the statutory requirement for portable appliance testing.
The EasyPAT 1600 is quick and easy to use, carrying out the mandatory earth bond and insulation tests plus a fuse test in the minimum possible time. The earth continuity tests can be carried out at 8A, 25A and 100mA, enabling the complete range of appliances including personal computers to be tested, with each current rating easily selectable by a simple rocker switch.
The EasyPAT 1600 is able to test both 230V and 110V appliances and, with its built-in 230V IEC and extension lead tester and removable earth bond lead, offers maximum flexibility. With labels showing the date of test and results also available from Glanford Electronics, the EasyPAT 1600 is the complete, low cost solution to statutory PAT testing in one, easy to use package.

Specifications
Does both mandatory tests and has a built in fuse test
25A, 8A and 100mA (for computers, etc) earth bond tests selectable with a simple rocker switch
Incorporates an extension lead tester to test IEC leads (can also be used to test 110V extension leads with a MAREX331 adaptor).

   EasyPat2100 Portable Appliance Tester
A high speed, fully specified dual voltage PAT tester which is ideal for contractors and workshops. Simple push button test selection maximises productivity. With an excellent test result display, the EasyPAT 2100 is the best choice in manual operation testers.
Does ALL 5 tests. Tests at either 110V or 240V, dependant on supply voltage.
No need for computer links

Specifications
Tests 110V and 240V Appliances.
Earth Continuity (Bond): 0-1.99Ω at 8A, 25A and 100mA.
Insulation Test: 0-19.9Ω at 500V DC.
Run Test: 0-3.1 kVA.
Earth Leakage Test: 0-6mA AC.
Flash Test: 1.5kV AC Class I, 3.OkV AC Class II.
Autoselection of 240/110V.
Supplied with manual, earth bond lead and flash probes.

   MicroPAT+ Portable Appliance Tester
The MicroPAT+ has improved internal design to speed up testing & downloading and allows user selection of pass levels. This is the fastest to use computerised tester available today and it will significantly increase your productivity. Tests show that a simple test selection procedure with dedicated buttons for each test is the fastest way to do PAT testing. Compatible with PATS, Shire Safety First and Safety First Express software. Optional barcode reader interprets industry standard barcodes.
Downloads to printer/computer.  Dual voltage 240 & 110V.  Earth leakage & operation tests.  Earth bond at 25A & 100mA.  Flash test with pistol probe.

Specifications
Earth Continuity (Bond):
0-1.9952 at 25A and 100mA
Pass level selectable 0.1 - 0.5Ω in 0.1Ω steps
Insulation Test: 0-19.9Ω at 500V DC
Run Test: 0-3.1 kVA
Earth Leakage Test: 0-6mA AC
Flash Test: 1.5kV AC Class I, 3.OkV AC Class II
Tests 110 & 240V appliances
Autoselection of 240/110V
Supplied with manual, earth bond lead and safety gun for insulation and flash testing.
Proffessional 2500 17th/Part P Installation Kit
This kit complies fully with Part P. Within the strong case is a highly specified insulation tester, which has polarisation index and dielectric absorption ratio functions, and RCD tester. The non trip earth tester quickly calculates PSC & PFC as well as allowing hands free PE & PN loop testing. The instruments come in a foam lined aluminium case with fused and unfused test leads.

Does everything for compliance with Part P
High spec insulation tester
Polarisation index and dielectric absorption ratio functions
Earth Loop Test with quick calculation of PSC & PFC
Hands free PE & PN loop testing
Effortless, rapid RCD testing
Aluminium case with high density foam inlay for long life

FD500 Fuse Finder

Glanford Electronics Limited now stocks the "gadget" that could save all Electricians much embarrassment and time.
Have you been in the position of trying to find that fuse or circuit breaker in a factory power switchboard? Have you been in an office where you need to draw the fuse to isolate a circuit, pulled the wrong fuse, cut-off the office computers, and received a severe ticking off? At some time or other, most of us have. Look no further, Martindale Electric have the answer in their " Fuse Finder Kit ", (AC circuits 200-250volts).
The analogue Martindale Fuse Finder Kit (FD500) finds which fuse or breaker controls a circuit. It also enables tracing from socket to socket on a circuit.
The transmitter (FD500/T) takes its power from the mains and emits a signal which the adjustable sensitivity receiver (FD500/R) can pick up.
This combination can easily distinguish the appropriate circuit, even on a crowded fuse board.
Sensitive analogue adjustment by thumb wheel finds the right breaker rapidly.
   EZ 150 E-Ze Check™ Extra

Non trip earth loop impedance checker
A revolutionary new earth loop indicator with voltage and wiring checks. Conventional indicators have the weakness that they only tell you if the earth is connected, they don't tell you how safe it is. Martindale's new T-Safe™ Technology gives safe, earth loop impedance checking within carefully selected bands without tripping the RCDs.

Features
Non-trip earth loop test
Voltage test
Socket test
T-SafeTM technology
Identifies faults other checkers can't
For use in 13A mains socket only

Specifications
Nominal supply: 230V, 50 Hz
Earth loop impedance span: 0-1.7Ohms, 1.7 to 5Ohms, 5 to 10Ohms, 10 to 100Ohms, 100 to 200Ohms, 200 to 500Ohms
Earth loop threshold accuracy: ±(10% + 0.3Ohms)
Voltage low indication: <195V Voltage high indication: >270V
Open earth indication: >500Ohms
Dimensions: 65 x 65 x 50mm
Weight: Approx. 64g
Power consumption: <1.6 W
Overvoltage: Cat II / 300 V
Pollution degree: 2
   EZ 2100

A revolutionary new 17th Edition tester with T-Safe™ non-trip earth loop impedance check.

Features

non-trip earth loop test
voltage test
socket test
Test readings scroll through in sequence on the clear, back lit, 32 character display to show socket problems, or high/low voltage conditions. Then the earth loop impedance test result is displayed.
Specifications

Nominal operating voltage: 230 V AC, 50 Hz
Non-trip Earth loop impedance ranges:
0.1 to 8.99 Ohms(0.01Ohms resolution)
9 to 89.9Ohms(0.1Ohmsresolution)
90Ohmsto 3kOhms(1Ohmsresolution)
Earth loop accuracy: ±(3% of reading + 0.1Ohms+2 digits)
Voltage indication: low <195 V, high >270 V
E-N voltage fault threshold: 30V
Open earth indication:
3k to 70k ">3kvOhms"
>70k "open earth" (current less than 3.5mA)
Power supply: From mains, no batteries required
Power consumption: Typical 4.5mA, max 7mA, <2VA
Dims: 140mm x 80mm x 55mm
patent pending

Glanford Electronics can supply, repair and calibrate the range of Martindale instruments.
Please send for Brochures or visit their website on www.martindale-electric.co.uk

Martindale was founded in 1928 and has been manufacturing test equipment continuously since that time. As an approved stockist of Martindale Electric, Glanford Electronics Ltd can supply, repair and calibrate Martindale's range of test equipment. We would be pleased to give advice on which test equipment would suit your needs.
Martindale Micropat Plus Bundle The Martindale Micropat Plus Bundle includes labels, software, download lead and a barcode reader to speed up testing & prevent errors, as well as 1000 combined barcode and test labels and a packet of fail labels. A set of 3-phase adaptors allows 3-phase equipment to be tested. The IEE Code of Practice gives full guidance on PAT test theory and practical tips. This kit has everything needed to start testing straight away.				HPAT600 Hand Held PAT for faster testing The HPAT600 offers profitability gains for service companies and productivity gains for health & safety officers, premises & facilities managers and other users, for example school caretakers. Battery powered for lightweight and easy use, it’s supplied with mains leads and a car charger, crammed with features such as dual insulation test voltage, user selectable pass levels, easy (manual) or fast (automatic) operating mode, IEC lead test insulation, polarity, backlight, test lead null out feature, simulated load test and test data storage for up to 200 appliances - equivalent to a whole day’s testing. It tests class I, class II appliances and power cords. It incorporates a 250V insulation test for sensitive IT equipment and appliances with mains filters. A 200mA DC earth continuity test is safe for all appliances and complies with the new code of practice for PAT testing. Limits can be set by managers to suit their own requirements eg. to identfiy appliances without borderline passes. In manual mode, a connection diagram for the selected test type is shown on the display. Each step of a test requires user confirmation by a press of the OK button. In the automatic mode, it will quickly run through a selected test sequence without any further user interaction unless a failure is encountered. All these features make it the PAT of choice for implementing an efficient and cost effective portable appliance testing solution. Complete with free Certificate of Calibration..				The HPAT600 is a battery powered portable Appliance Tester with the following features:- Dual Insulation Test Voltage - The insulation measurement test voltage can be set to either 500V or 250V. User Selectable Pass Levels - Appliance test pass levels may be user defined. Easy or Fast Operating Modes - The HPAT600 can be operated in either of two modes. In manual mode, aimed at the newcomer to PAT testing, a connection diagram for the selected test type is shown on the display. Each step of a test requires user confirmation by a press of the OK button. In the Auto mode, for the experienced operator, the HPAT600 will automatically run through a selected test sequence without any further user interaction unless a failure is encountered. IEC Lead Test - The HPAT600 can also be used to check IEC leads for earth continuity, insulation, and polarity. Test Data Memory Storage - The HPAT600 is able to store test data for up to 200 appliances into memory. Now Available!


Martindale Veritest 2230 The VERITEST 2230 is being offered at a very special price that just cannot be missed. This all in one tester,ideal for Part P requirements, incorporates continuity, insulation resistance, RCD,non trip earth loop impedance, and phase rotation tests. This unit is smaller and more compact than other machines on the market, which makes it very comfortable to use in confined areas. Although supplied in a carry case which allows hands free use, the unit can also be comfortably held in one hand. Specifications Insulation Ranges: 0.05MOhms to 1999Ohms at voltages between 50VDC, 100VDC, 250VDC, 500VDC, 1000VDC with a resolution of 0.01MOhms,0.1MOhms & 1MOhm. Continuity Ranges: 0.01Ohms-19.99Ohms (0.01Ohms res) 20.0-99.9Ohms (0.1Ohms res) RCD Ranges: 10ma, 30ma, 100ma, 300ma, 500ma. Non Trip Earth Loop Ranges: 0.034-19.99Ohms (0.01Ohms res), 20.04-199.9Ohms (0.1Ohms res), 2004-1999Ohms (1S2 res) Phase Rotation Test: Yes Weight: (batteries included) 1000gm Dimensions: 222mm(L), 162mm(W), 57mm(D) Working Temperatures: -10°Cto+50°C Live Circuit Warning: Yes Supplied complete with test leads, soft carry case & Quickstart user guide as well as a comprehensive user manual	Veritest 2240 All in one Tester We are proud to introduce the VERITEST 2240 to the Martindale range of test equipment. This all in one tester incorporates continuity, insulation resistance, RCD, earth loop impedance, global earth resistance and phase rotation tests. This unit is smaller and more compact than other machines on the market, which makes it very comfortable to use in confined and hazardous areas. Although supplied in a carry case which allows hands free use, the unit can also be comfortably held in one hand. The Veritest also has the ability to commit test results to its internal memory and is equipped to download to a P.C. via optional software and accessories. Specifications Insulation Ranges: 0.1 Ohms to 1999Ohms at voltages between 50VDC, 100VDC, 250VDC, 500VDC, 1000VDC with a resolution of 0.01Ohms,0.1Ohms and 1Ohms Continuity Ranges: 0.01Ohms-19.99Ohms (0.01Ohms res) 20.04-99.9Ohms (0.1Ohms res) RCD Ranges: 10ma, 30ma, 100ma, 300ma, 500ma. Non Trip Earth Loop Ranges: 0.034-19.99Ohms (0.01Ohms res), 20.04-199.9Ohms (0.1Ohms res), 2004-1999Ohms (1S2 res) Global Earth Resistance Range: 1-1999Q Memory Slots For Saved Tests: 350 Phase Rotation Test: Yes Weight: (batteries included) 1000gm Dimensions: 222mm(L), 162mm(W), 57mm(D) Backlight: Yes Working Temperatures: -10Cto+50C Live Circuit Warning: Yes	Veritest 2250 All in one Tester This is our flagship multi tasking all in one 17th edition tester. Incorporating all of the functions of the VERITEST 2240, with the added functionality of a power analyser and earth resistivity and environmental tests, such as temperature, relative humidity, air speed, illuminance and sound level which can be carried out with additional accessories (purchased separately). This is a fully specified machine that not only offers powerful testing capabilities to the electrician, but also is an invaluable tool for power, distribution, environmental and cabling organisations alike. Main Features Continuity Test Insulation Resistance Test Non Trip Earth Loop Test RCD test Phase Rotation Test Power Analyser Earth Soil Resistivity 999 Memory Slots Downloadable to PC Backlight Auto Power Off Carry Case

General Purpose Multimeter MM34 This new, low cost multimeter has 4 main functions together with diode and battery test and a large clear display. The sculpted shape makes it comfortable to hold and easy to position the central rotary switch. Specifications General Purpose Multimeter MM34 31/2 digit LCD display with automatic polarity indication and automatic zero. AC V: 100mV to 600V (2 ranges) (50Hz to 500Hz) DC V: 1 mV to 600V (4 ranges) DC A: 0.1 pA - 10A (5 ranges) Ohms: 10m4 to 20MΩ (5 ranges) Diode test Battery test:1.5V & 9V Dimensions: 143 x 68 x 47mm Includes: test leads, battery and user manual.	Digital Clampmeter CM51 The Martindale CM51 is a low cost 200A mini clamp meter with autoranging,display hold and auto power down. The two ranges mean that when measuring 40A and lower currents the resolution increases from 100mA to 10mA. Autoranging ensures that the most suitable range is always automatically selected. This small current clamp will fit into your shirt pocket for maximum convenience. The small jaws make it easy to use and the 200A AC range accurately covers the majority of applications. Specifications 3½ digit LCD display with anunciators Display hold DH button Display update 25 times per second AC A: 10mA to 200A, autoranging (2 ranges) (40Hz to 500Hz) Max conductor: 27mm Ø Operating temperature: 0° to 40°C at <80% RH Auto Power off after 10 mins Low battery warning: “BAT” symbol Overrange indication: “OL” symbol Dimensions: 150 x 52 x 24mm Weight: 110g Overvoltage: Category III, 300V Includes: battery, carry case and user manual With Free Calibration Certificate.	Digital Insulation Tester IN2001 The IN2001 insulation tester is amazing value for money. With an automatic zero adjust feature to remove the resistance of the leads, you are guaranteed fast, accurate continuity testing at 200mA. The IN2001 has a stable 500V test voltage and a 200mA continuity test, fully meets all relevant regulations: BS7671, HD384 and BS EN 61557.This supercedes the Metrohm I6D500 Single range tester This supercedes the Metrohm 16A500 Specifications Insulation: 10kohms to 100Mohms at 500V Continuity: 0 - 200ohms, 0.01ohms resolution (audible tone <1ohm) Voltage range: 500V AC Complies with: BS EN 61557 and 17th Edition Dimensions: 190 x 90 x 54mm Includes: quality soft protective carry case, test leads, battery and user manual.

17^th EDITION INSTALLATION TESTERS IN2003 Insulation Tester The IN2003 insulation and continuity tester gives 250, 500 & 1000V tests. The top of the range IN2003 insulation tester comes with all the facilities you need to do professional testing. With an automatic zero adjust feature to remove the resistance of the leads, you are guaranteed fast, accurate continuity testing. The three test voltages allow you to carry out the widest range of testing. A major advantage of this design is that you can set the test button to be either latching to give a permanent output or 'press to test' with the option of switching between these two ways of working at any time. A professional product for professional electricians! Specifications Insulation test at 250 / 500 / 1000V. 0-200Ω continuity range (buzz <1Ω), 0.01Ω resolution. 0-100MΩ (500V) 0-200MΩ (1000V). 500V AC range. Complies with BS EN 61557 (16^th Edition). Dimensions: 190 x 90 x 54mm. Replacement leads - order code: TL47. Optional fused test leads - order code: TL57. Supplied with batteries, instructions, quality case and leads.	LP2000 Loop Tester The LP2000 is a fast and accurate autoranging loop tester and is the lowest cost 16^th Edition earth loop impedance tester available. It can carry out phase earth and phase neutral testing and it automatically displays PSC readings. A wander lead for testing bonded metalwork is also supplied. Specifications Range: 0.01 to 200Ω (Autoranging). Resolution: 0.01 and 0.1Ω Ipsc: 0-19.99kA in steps of 0.001 kA (10A). Dimensions: 190 x 90 x 54mm. Complies with BS EN 61557 (16^th Edition). With case, standard mains lead and wander lead. Optional leads for testing at distribution boards and luminaries TL85 or TL88.	RC2000 RCD Tester The RC2000 is a very fast and easy to use RCD tester, suitable for all common RCDs. All you need to do is select the test current and then swap between half the current, when the trip should stay open and the test current itself, when the RCD should trip. A second toggle switch allows you to test, as required, for opposite sides of the current cycle. Specifications Full trip settings: 6mA-10-30-100-300-500mA. Half trip settings: 3mA-5-15-50-150-250mA. Fast trip settings: 150mA (full trip of 6, 10 and 30mA only). Switchable selection of test cycle 0 / 180°. Timing range: 0 - 1999mSec in steps of 1 mSec. Timing accuracy: ±2% of reading ±1 digit. Dimensions: 190 x 90 x 54 mm. With case and 13A mains lead. Optional lead for distribution boards - order code: TL88. Complies with BS EN 61557 (16^th Edition).

CM56 1000 Autoranging clamp The CM56 has a large display combining a clear 3¾ digit readout with a responsive 34 segment bar graph which indicates fluctuating readings. For general purpose measurements it has autoranging AC and DC voltage and measures resistance to 30MΩ with a beeper on the low resistance continuity range. It also measures frequency with 0.1 Hz resolution allowing accurate determination of mains or generator frequencies. Hold and AC peak functions assist in taking readings in awkward places. Specifications AC Current: 0-32-320-1000A. AC Volts: 0-3.2-32-320-600V autoranging. DC Volts: 0-320m-3.2-32-320-1000V autoranging. Resistance: 0-320-3.2k-32k-320k-3.2M-30MΩ Frequency: 0-320-3.2kHz-32kHz. Max. conductor: 57mmØ or 70 x 18mm bar. With carry case and leads.	PC15250 Phase Rotation & Continuity Indicator The PC 15250 continuity indicator will quickly and simply prove continuity of all three lines, or identify which are faulty and it also shows the sequence of phase rotation. A fast, effective method of identifying worn or unmarked cables, and ensuring all 3-phase outlets and machinery are wired correctly. The retractable probe shields give a choice between long exposed tips for reaching inaccessible contacts and safer, shorter lengths of bare tips for increased safety. Supplied with one fused crocodile clip and two fused prod type probes with retractable shrouds this unit is fully compliant with GS38 and BS EN 61010. Features Include: Proves continuity Identifies fault lines Phase rotation	EasyPat1600 Manual Portable Appliance Tester Martindales EasyPAT 1600 Manual PAT Tester, is a cost effective and easy to use tester for anyone who just needs to the minimum to comply with the statutory requirement for portable appliance testing. The EasyPAT 1600 is quick and easy to use, carrying out the mandatory earth bond and insulation tests plus a fuse test in the minimum possible time. The earth continuity tests can be carried out at 8A, 25A and 100mA, enabling the complete range of appliances including personal computers to be tested, with each current rating easily selectable by a simple rocker switch. The EasyPAT 1600 is able to test both 230V and 110V appliances and, with its built-in 230V IEC and extension lead tester and removable earth bond lead, offers maximum flexibility. With labels showing the date of test and results also available from Glanford Electronics, the EasyPAT 1600 is the complete, low cost solution to statutory PAT testing in one, easy to use package. Specifications Does both mandatory tests and has a built in fuse test 25A, 8A and 100mA (for computers, etc) earth bond tests selectable with a simple rocker switch Incorporates an extension lead tester to test IEC leads (can also be used to test 110V extension leads with a MAREX331 adaptor).