TPI 775 Combination CO & Combustible Gas Leak Detector

TPI 775 Combination CO & Combustible Gas Leak Detector

Tietzsch MegaSafe ISO 1Ex ATEX Insulation Tester

Tietzsch MegaSafe ISO 1Ex ATEX Insulation Tester Part No. 83310

Tietzsch MultiSafe DSP 4 Voltage Tester Part No. 84402

As low as £210.00 £175.00
Availability: In stock
Only %1 left
SKU
Tietzsch MultiSafe DSP 4 Voltage Tester

The Tietzsch MultiSafe DSP 4 Voltage Tester is a two-pole voltage tester with digital display. It complies with DIN EN 61243-3 (VDE 0682 part 401) and is provided with continuity and phase tester, polarity tester and phase sequence indicator.

Comes complete with a calibration Certificate Traceable to National Standards when purchased new.

The Tietzsch MultiSafe DSP 4 Voltage Tester is a two-pole voltage tester with digital display. It complies with DIN EN 61243-3 (VDE 0682 part 401) and is provided with continuity and phase tester, polarity tester and phase sequence indicator. With this device you can determine the existence and the strength of AC and DC voltages within a range of 24 V to 1000 V at frequencies up to 4 kHz.

With the integrated continuity tester, you can also measure resistances within a range of 0 to 1999 kΩ. Voltage and resistance values appear in digital format on the display. Additionally, three LEDs indicate voltage and rotating field as well as one LED and one sound generator continuity. Due to its high protection category IP 65 the Tietzsch MultiSafe DSP 4 Voltage Tester can be used in precipitation. The ST-version has adjustable electrode length 4 or 15 mm.

Voltage tester:

  • precise display of the voltage 1 V up to 1200 V AC / 0,01 up to 1500 V DC
  • resistant to voltage – CAT IV 600 V – VDE certified
  • clear LED indicator for dangerous voltage
  • hold the measured value with the HOLD key
  • large illuminated display

Continuity tester:

  • continuity test with sound
  • resistance measurement in the range of 0,1 kOhm to 2000 kOhm
  • green LED for continuity

Phase and phase sequence tester:

  • phase tester with display “POL”
  • phase sequence tester with LED display left / right
  • phase and phase sequence tests can also be performed with insulating gloves
  • additional phase sequence testing without ground reference for IT power grids

Other functions:

  • ST-version slim test electrodes for tight terminal blocks (adjustable electrode length 4 or 15 mm)
  • easy operation
  • insulation fault detection by two-color cable insulation
  • IP 65 – waterproof

 


Tietzsch MultiSafe DSP 4 Voltage Tester features:

  • Nominal voltage range:
  • 24* ... 1000 V AC/1500 V DC
    *Auto on from 24 V
  • Overvoltage range
  • (exceeds the limit values in accordance with IEC 61243-3):
    > 1000 V AC ... 1200 V AC
  • Nominal frequency range:
  • 0 ... 500 Hz
  • Extended frequency range
    (exceeds the limit values in accordance with IEC 61243-3):
  • 15 Hz ... 10 kHz < 500 V,
    15 Hz ... 4 kHz > 500 V
  • Input resistance:
  • approx. 320 k. AC
    approx. 710 k. DC
  • Current (Peak value Is):
  • 3,2 mA at 1000 V AC
    1,4 mA at 1000 V DC
  • On-period:
  • 2 minutes
  • Display:
  • 4 LEDs for voltage, continuity, & phase sequence
    LCD digital display 7-segment-figure,
    2 lines 0 ... 1999-digit backlight 3 measurement
  • DSP 4 ST
  • Adjustable electrode length 4 or 15 mm
  • Power supply:
  • 9 V block battery
    IEC 6LR61 (alkali-manganese), multi-stage display of battery status
  • Surge voltage category:
  • CAT IV 600 V
    CAT III 1000 V
  • Impulse withstand voltage:
  • > 12 kV (1,2/50 µs)
  • Test voltage:
  • 6 kV
  • EMV-requirements:
  • DIN-EN 61326
  • Operating temperature:
  • -15…+45°C
  • Casing:
  • impact-resistant, dustproof plastic casing with unbreakable display cover
  • Protection category:
  • IP65
  • Connecting line:
  • PUR hose cable 1000 V, 1m
  • Dimensions:
  • test electrode with display, 240 x 62 x 39 mm
  • Weight:
  • 270 g (incl. battery)

 

Glanford Electronics is a Tietzsch UK Distributor

Tietzsch MultiSafe DSP 4 Voltage Tester comes complete with a calibration Certificate Traceable to National Standards when purchased new.

Contact us for further information regarding Tietzsch MultiSafe DSP 4 Voltage Tester

 

Write Your Own Review
You're reviewing:Tietzsch MultiSafe DSP 4 Voltage Tester Part No. 84402
Your Rating

Our Best Selling Products